[MasterCAM] 求一个新代21TB的车铣复合后处理

wen36

新代21TB的车铣复合后处理，X上方向4个动力头，Z上方向4个动力头的后处理; 动力头上方向XJ是负方向

优胜模具

MasterCAM没研究，UG可以吗？请上传nc程序样本

wen36

优胜技术支持 发表于 2019-10-17 10:07
MasterCAM没研究，UG可以吗？请上传nc程序样本

已上传MasterCAM程序样本，我同事是UG可以分享一下，谢谢

wen36

优胜技术支持 发表于 2019-10-17 10:07
MasterCAM没研究，UG可以吗？请上传nc程序样本

G99 G40
T0101
G00 X45. Z30. M08
M03 T0101 S1000
G00 Z0.1
G01 X-1. F0.3
G00 X40. Z2.
G01 Z0. F0.3
X42.2 Z-1. F0.3
Z-8.6
G00 X45. Z150. M09
M01
N2 M03 T0202 S1000
G00 X45. Z30. M08
Z0.
G01 X-1. F0.1
G00 X39.85 Z2.
G01 G42 Z0. F0.3
X41.85 Z-1. F0.08
Z-8.5
U1.
G00 G40 X45. Z150. M09
M01
N3 M03 T0303 S500
G00 X43. Z30. M08
Z2.
G76 P020060 Q100 R0.05
G76 X40.7 Z-8. P650 Q300 F1.
G00 X45. Z150. M09
M01
N5 M03 T0505 S1000
G00 X0. Z30. M08
Z2.
G74 R0.3
G74 Z-15. Q10000 F0.1
G00 Z250. M09
M05
M01

(2 平底刀)
N15 M45
T1414
M64 S2000
G0 G54 X-8.623 Z30.
C-20.064
Z2.
G98 G01 Z-5.3 F500.
X-8.234 C349.647
X-8.1 C359.899
X-8.228 C370.126
X-8.394 C375.213
X-8.623 C380.064
X-8.854 C383.23
X-9.169 C385.98
X-9.556 C388.244
X-10. C390.
X-9.556 C391.756
X-9.169 C394.019
X-8.854 C396.769
X-8.623 C399.936
X-8.234 C409.647
X-8.1 C419.899
X-8.228 C430.127
X-8.394 C435.215
X-8.623 C440.064
X-8.854 C443.232
X-9.169 C445.981
X-9.556 C448.245
X-10. C450.
X-9.556 C451.755
X-9.169 C454.018
X-8.854 C456.768
X-8.623 C459.936
X-8.234 C469.647
X-8.1 C479.899
X-8.228 C490.126
X-8.394 C495.214
X-8.623 C500.064
X-8.854 C503.23
X-9.169 C505.979
X-9.556 C508.242
X-10. C510.
X-9.556 C511.754
X-9.169 C514.018
X-8.853 C516.768
X-8.623 C519.936
X-8.234 C529.647
X-8.1 C539.899
X-8.228 C550.126
X-8.394 C555.213
X-8.623 C560.064
X-8.854 C563.23
X-9.169 C565.98
X-9.556 C568.244
X-10. C570.
X-9.556 C571.756
X-9.169 C574.019
X-8.854 C576.769
X-8.623 C579.936
X-8.234 C589.647
X-8.1 C599.899
X-8.228 C610.127
X-8.394 C615.215
X-8.623 C620.064
X-8.854 C623.232
X-9.169 C625.981
X-9.556 C628.245
X-10. C630.
X-9.556 C631.755
X-9.169 C634.018
X-8.854 C636.768
X-8.623 C639.936
X-8.234 C649.647
X-8.1 C659.899
X-8.228 C670.126
X-8.394 C675.214
X-8.623 C680.064
X-8.854 C683.23
X-9.169 C685.979
X-9.556 C688.242
X-10. C690.
X-9.556 C691.754
X-9.169 C694.018
X-8.853 C696.768
X-8.623 C699.936
G0 Z30.
M69
M44
Z150. M09
M01
M05
T0101
G00 X42. Z0.2
M30

郑国毅

和我的机器一样。

4660

我有Mastercam2017-2021新代4+4车铣复合中文后处理加威新176零七603926

做自己想做的事

优胜技术支持 发表于 2019-10-17 10:07
MasterCAM没研究，UG可以吗？请上传nc程序样本

最后有后处理文件吗？